How to Remove Harley Ignition Switch Without Key

If you need to remove your Harley ignition switch but don’t have a key, there are a few ways you can do it. One is to use a flathead screwdriver to pry off the cap on the switch. This will expose the screws that hold the switch in place.

Another way is to drill out the rivets that hold the switch in place. Be careful not to damage any of the wirings when doing this.

• Locate the ignition switch on the Harley
• This is usually on the handlebars near the throttle
• Using a small screwdriver, insert it into the slot on the back of the ignition switch
• Turn the screwdriver until you feel resistance, then continue turning until the ignition switch pops out
• Disconnect any wires that are attached to the ignition switch and remove it from the motorcycle

How Do You Remove an Ignition Switch Without the Key?

Assuming you don’t have the key and can’t hotwire the car, the only way to remove the ignition switch is to disassemble the steering column. This is a difficult and time-consuming process, so it’s best to consult a professional if possible. If you’re determined to do it yourself, here are some instructions:

1) Disconnect the negative battery cable.

2) Remove the airbag module from the steering wheel.

3) Unscrew and remove the steering wheel itself.

4) Locate the ignition switch assembly under the steering column. It will be attached with several screws.

5) Remove these screws and carefully disconnect any wiring harnesses connected to the ignition switch.

Be sure to note where each wire goes so you can reconnect them later. With all wires disconnected, you should now be able to remove the ignition switch completely.

How Do You Start a Harley Without the Key?

Assuming you’re talking about a modern Harley with an electronic ignition: To start a Harley without the key, you’ll need to find the hidden starter button. This is usually located on the right side of the motorcycle, near the rider’s leg.

Once you’ve found the button, press and hold it for a few seconds. The motorcycle should start up automatically. If it doesn’t, then you may need to jump-start it using another vehicle.

How Do You Pop Out an Ignition Switch?

Assuming you need to replace an ignition switch: The first step is to disconnect the negative battery cable. Once that is done, locate the ignition switch and unscrew any screws or bolts holding it in place.

You may need a screwdriver or socket set to do this. With the screws removed, gently pull the ignition switch out from its housing. There will be wires attached to the back of the ignition switch.

Using a wiring diagram for your specific vehicle, carefully remove each wire from its terminal and label them so you know where they go back on. You can also take a picture with your phone for reference. With all of the wires detached, slide the new ignition switch into place and reattach each wire one at a time according to your labels or picture reference.

Make sure each wire is firmly seated in its terminal before moving on to the next one. Once all of the wires are reconnected, screw the new ignition switch into place (using either new or existing screws/bolts). Reconnect the negative battery cable and test out your new ignition switch!

How Do You Remove the Ignition Switch on a 2013 Harley?

Assuming you need to replace the ignition switch: The first step is to disconnect the battery. Next, remove the upper fairing assembly.

There are four bolts that hold it in place, two on each side. Once the fairing is off, you will have access to the ignition switch. There are three wires that connect to the back of the ignition switch- a black wire, a brown wire, and a green wire.

The black wire is ground, the brown wire is power from the battery, and the green wire is power from the accessory position on the key switch. To remove the ignition switch, first, remove these three wires. Next, there are two screws holding it in place which can now be removed.

The last step is to simply pull the outwards on the ignition switch itself until it comes free from its housing.

Harley Ignition Switch Cover Removal

Harley Ignition Switch Cover Removal The ignition switch cover on a Harley Davidson motorcycle is held in place with two screws. The cover itself is made of metal and has the words “Harley-Davidson” engraved into it.

This piece protects the ignition switch and wiring beneath it from damage. If your cover is damaged, you will need to replace it to protect your investment. To remove the ignition switch cover, start by removing the two screws that hold it in place.

Next, pry the cover off of the ignition switch using a flathead screwdriver. Be careful not to damage the paint around the ignition switch. Finally, disconnect any wires that are still attached to the back of the cover and discard the old piece.

Now you can install your new ignition switch cover by following these same steps in reverse order. Make sure that all wires are properly connected and that the two screws are tightened securely before riding your motorcycle again. With a fresh new cover in place, you can rest assured knowing that your Harley’s ignition system is well protected!

Harley Ignition Switch Problems

If you own a Harley, you may have experienced ignition switch problems. The ignition switch is responsible for turning the bike on and off, and if it’s not working properly, it can be a major inconvenience. There are a few different things that can cause ignition switch problems, and luckily, most of them are relatively easy to fix.

One of the most common causes of ignition switch problems is a bad connection between the switch and the battery. If your bike has been sitting for a while, the connections may have become corroded. Cleaning the connections with a wire brush will usually fix the problem.

Another common problem is that the key itself may be worn out. Over time, the teeth on the key can become worn down, making it difficult to turn the ignition switch. Replacing the key is typically all that’s needed to fix this problem.

If your Harley’s ignition switch isn’t working properly, don’t despair – chances are good that it’s a simple issue that you can easily fix yourself.

Harley Toggle Ignition Switch

If you’re a Harley rider, then you know the importance of having a toggle ignition switch. This simple device allows you to turn your bike on and off with the flick of a switch. But what exactly does a toggle ignition switch do?

A toggle ignition switch is a mechanical device that connects or disconnects the power supply to the engine. It’s usually located on the handlebars near the rider’s right hand. When you flip the switch to the “on” position, it completes an electrical circuit that sends power to the spark plugs, igniting the fuel and allowing the engine to start.

Flipping it to the “off” position breaks that circuit, shutting down power to the engine and effectively killing it. Most Harley riders keep their toggle ignition switch in good working order, but occasionally they may need to replace it due to wear and tear or accidental damage. If you find yourself in need of a new toggle ignition switch, there are a few things you’ll need to know before making your purchase.

First, make sure you get one that’s compatible with your specific model of Harley motorcycle. There are many different types of Harley motorcycles out there, so not all switches will fit all models. Second, take note of any special features your current switch has (like illuminated buttons) so you can get an identical replacement.

Finally, be prepared to pay around $50 for a new toggle ignition switch – while this may seem like a lot, it’s actually quite reasonable considering how important this little device is to keep your bike running smoothly!

Conclusion

If you need to remove your Harley ignition switch without a key, there are a few steps you’ll need to follow. First, locate the two screws that hold the switch in place. Next, use a small flathead screwdriver to pry out the pin that secures the wiring harness.

Finally, remove the switch and disconnect the wires.